1. Home
  2. Resources

Gauge chart, mixer guide and spec sheets

Reference material for resellers and their customers. Every figure comes from our own specification tables.

Needle gauge chart

Bore and outside diameter per gauge for our stainless steel needles with a Luer hub. Figures are nominal, taken from families LS-DSP-101, LS-DSP-103, LS-DSP-104, LS-DSP-115, LS-DSP-125, LS-DSP-132, LS-DSP-134, LS-DSP-137.

Gauge to ID and OD, with our hub color
GaugeID mmOD mmID inOD inOur hub colorAlso listed as (ID / OD mm)
13G1.902.400.0750.094Clear-
14G1.552.080.0610.082Olive1.80 / 2.00 in LS-DSP-1151.60 / 2.11 in LS-DSP-132
16G1.151.600.0450.063Gray1.25 / 1.65 in LS-DSP-115
18G0.841.270.0330.050Green0.86 / 1.26 in LS-DSP-1010.84 / 1.26 in LS-DSP-1030.84 / 1.28 in LS-DSP-115
20G0.600.900.0240.035Pink0.60 / 0.91 in LS-DSP-134, LS-DSP-1370.61 / 0.91 in LS-DSP-115
22G0.400.700.0160.028Blue0.41 / 0.72 in LS-DSP-132, LS-DSP-134
25G0.250.500.0100.020Red0.25 / 0.51 in LS-DSP-115, LS-DSP-134, LS-DSP-137
27G0.200.400.0080.016Clear-
30G0.150.300.0060.012Lavender-

Where our families list slightly different figures for the same gauge (6 of 9 gauges), the table shows the value listed in most families and the others alongside it. The product page for each SKU carries its own figures.

Hub colors are our hub color only. Color coding is not standardized between suppliers or brands, so confirm a gauge by the gauge marking or a measured ID, never by color alone.

Static mixer guide

A static mixer has to fit the cartridge first and mix the material second. Pick the inlet type, then the element count.

Inlet types in our range

Inlet type
Bayonet
Inlet
Bayonet inlet that pushes on and twists to lock.
Used on
Two-part cartridges with a bayonet outlet.
Elements in our range
7 to 21
Bayonet mixers: 6 variants
Inlet type
MB series
Inlet
MB-style inlet for 1:1 two-part cartridges.
Used on
1:1 two-part cartridges with an MB-style outlet.
Elements in our range
16 to 20
MB series mixers: 6 variants
Inlet type
Round mouth
Inlet
Round-mouth inlet that seats on the cartridge or valve outlet.
Used on
Two-component cartridges and dispensing valves.
Elements in our range
8 to 24
Round mouth mixers: 16 variants

Cartridge and mixer not made for each other? Some interfaces are broadly shared; proprietary quick-connect systems need an adapter made for that system. See mixer adapters and connectors.

Element count, mix quality and waste

  • Each element divides and folds the flow again. More elements give the material more passes to blend.
  • That only holds within the same element design. Element counts do not compare across different designs.
  • More elements add pressure drop and leave more material in the tube as waste at every change.
  • Harder-to-mix materials and higher ratios tend to need more elements.
  • Pick the shortest mixer that gives a uniform color and a full cure in a test bead. Streaks at the outlet mean the mixer is too short.

Matching the mixer to ratio and interface

  • On a cartridge system the two cylinders set the mix ratio. The mixer only blends what it receives.
  • At high ratios the minor component arrives as a thin stream. Those ratios need a mixer shaped to steer it before mixing starts, so tell us the ratio before ordering.
  • A, B, C and F inlets are not interchangeable. Confirm the cartridge system before choosing a mixer.
  • Mixer color does not identify the ratio across brands. Some systems use color for size, caps or series.

When to send us a sample

  • The cartridge comes from another supplier and you are not sure of the interface.
  • The cartridge uses a proprietary quick-connect outlet.
  • You want to replace a mixer your customer already uses and need the same outlet and element count.
  • For an adapter, send the center-to-center spacing of the outlet holes and the outside diameter of the outlet interface.

Send the cartridge part number or a sample cartridge, the mix ratio and the material. We confirm the fit and suggest element counts to test. Send it through the partner form.

Spec sheets

One PDF per product line, with every family and variant in our range. Customers may reuse them with their own customers.

Spec sheet downloads (PDF)
Product lineGroupFamiliesVariantsDownload
Blunt stainless needlesDispensing needles and tips480blunt-stainless-needles.pdf
Tapered tipsDispensing needles and tips212tapered-tips.pdf
Flexible tipsDispensing needles and tips126flexible-tips.pdf
PTFE lined needlesDispensing needles and tips15ptfe-lined-needles.pdf
Brush tipsDispensing needles and tips16brush-tips.pdf
Angled and bent needlesDispensing needles and tips335angled-and-bent-needles.pdf
UV blocking needlesDispensing needles and tips16uv-blocking-needles.pdf
Large bore and valve nozzlesDispensing needles and tips235large-bore-and-valve-nozzles.pdf
Threaded and special mountsDispensing needles and tips951threaded-and-special-mounts.pdf
Machine dispensing tipsDispensing needles and tips534machine-dispensing-tips.pdf
Custom and specialtyDispensing needles and tips528custom-and-specialty.pdf
Static mixersStatic mixers734static-mixers.pdf
Cartridges and applicatorsCartridges and applicators1327cartridges-and-applicators.pdf

Need a gauge, length or mixer outside these tables?